Test Campaign Coordination

Design, plan and execution of testing campaigns including scenario based human and non-human resource management and pipeline of necessary services and rentals. 

Equipment Mounting

3D scanning of existing components and design of specific target consoles for mounting reference sensors, markers and antennas for high-precision motion and positioning measurements. 

Measurement Environment

Installation of measurement technique and all surrounding components and peripheries including power management and safety button fitting.

Custom Wire Harness

Design and manufacturing of custom cable harnesses based on existing drawings or customer's needs incl. full documentation even in MIL Spec quality. On-site work assessment also available.

ADAS/AD Sensor Calibration 

A modular calibration and diagnostic toolkit for checking and adjusting environmental sensors that form the basis of active safety features in modern vehicles.

Suspension and Wheel Adjustment 

Instrumental measurement of the front and rear suspension of passenger vehicles and individual adjustment to the desired value. General lifting of vehicles on wheels or on a lifting point for further inspection and assembly tasks.

Mass Control 

Protocolled adjustment of vehicle test weight which is a standardized mass for testing, to ensure consistent and repeatable test results across different vehicles. Often including test dummies and any necessary equipment.

Two-axle 4WD Power Meter

The complex package is suitable for measuring the power delivered to the wheels of front-, rear- and all-wheel drive passenger vehicles, and then, supplemented with preliminary driveline loss measurements, for calculating engine power. 

Exhaust Gas Analyzer 

Gas composition measurement at a stable operating point, engine speed and oil temperature display during vehicle measurement. 

• CO 0…15 % vol.
• CO2 0…20 % vol.
• HC 0…30000 ppm vol.
• O2 0…25 % vol.
• NO 0…5000 ppm vol.
• Lambda 0…9999

• Smoke measurement 0…99.9 %

High-Voltage System Tester

Insulation testing of electric vehicle drives incl. guided measurement procedure and automatic documentation, calibration for reproducible accuracy.

• DC voltage: max. 1000 V
• Resistance: 0…10 MΩ

Serial Diagnostics for Passenger Vehicles

Fully PassThru compatible simultaneous diagnostics with built-in dual-channel oscilloscope and multimeter, and DoIP support.

• ISO 15031
• ISO 22900
• SAE J2534-1 & -2 (PassThru)
• ISO 9141-2 (K & L)
• SAE J1850 VPW & PWM
• High-Speed CAN ISO 11898
• ISO 15765-4 (OBD)

Serial Diagnostics for Commercial Vehicles

Diagnostic module specifically for heavy-duty vehicles, light-duty vehicles, tractors and buses.

Fuel Flow Meter

Fuel flow measurement without pressure drop.

• Range: -10…100 l/h
• Resolution:  0.050mm³
• Operating pressure: 0.02…20 bar
• Media temperature: -20…65 °C
• Accuracy: 0.3 % of measured value

Oscilloscope System for Vehicle Testing

Voltage, current, noise and vibration measurement on 8 channels for waveforms of sine, triangle, square, DC voltage, saw, sinc, Gaussian, half-sine, white noise, PRBS.

Handheld Thermal Imager

Surface temperature measurement of components in the ranges of -20…120 °C, 0…650 °C and 300…1500 °C.

Industrial Thermal Imager

Safety monitoring of the vehicle under measurement in the range of -20…1200 °C.

Cross-Border Assistance

Supporting your testing campaign on public road we provide technical rescue of faulty or damaged vehicle for neighboring area of Austria, Slovenia, Croatia and Hungary - ZalaZONE.

GRP/Parcel/Courier Transportation

Offering fast-acting transportation of vehicle parts and components for manufacturers and integrators as well as auxiliary- and test equipment for developers and test execution specialist.

Storing and Conditioning

Accessing workshop carport as an intermediate station to store your development vehicle. Increasing the efficiency minor conditioning tasks like data download, battery charging, system reset and configuration update can be conducted in the meantime.